BMGJJ - S/G LATEX ENAMEL WHITE & BASE

  • MSDS: BMGJJ
  • Manufacturer: PRESERVATIVE PAINT CO
  • Product Name: S/G LATEX ENAMEL WHITE & BASE
  • National Stock Number: 8010-00N024845
Product Identification

Product ID:S/G LATEX ENAMEL WHITE & BASE
MSDS Date:06/06/1989
FSC:8010
NIIN:00N024845
MSDS Number: BMGJJ

Responsible Party
PRESERVATIVE PAINT CO
5410 AIRPORT WAY SOUTH
SEATTLE, WA 98108
US

Emergency Phone: 206-526-2121; 206-634-5252

Info Phone: 206-763-0300

Cage: 86589

Contractor
PRESERVATIVE PAINT CO
80387 SEATTLE, WA 98108-1726 US

Cage: 86589

Ingredients

AMMONIUM HYDROXIDE

CAS: 1336-21-6

RTECS: BQ9625000

OSHA PEL 35 PPM STEL

ACGIH TLV: 25 PPM;35 PPM STEL

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS


MERCURY, (ACETATO)PHENYL-; (PHENYLMERCURIC ACETATE)

CAS: 62-38-4

RTECS: OV6475000

ACGIH TLV: 0.05 MG/M3 (MFR)

EPA Report Quantity: 100 LBS

DOT Report Quantity: 100 LBS


ETHYLENE GLYCOL

CAS: 107-21-1

RTECS: KW2975000

OSHA PEL 50 PPM, C

ACGIH TLV: 50 PPM, C

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB


TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


ALUMINUM SILICATE

CAS: 66402-68-4

ACGIH TLV: 10 MG/M3 (MFR)


ISOPROPYL ALCOHOL

CAS: 67-63-0

RTECS: NT8050000

OSHA PEL 400 PPM;500 PPM STEL

ACGIH TLV: 400 PPM;500 PPM STEL

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:MAY CAUSE IRRITATION OR BURNING
OF EYES. IF INGESTED MAY CAUSE GASTRO-INTESTINAL DISTRESS.
CHRONIC:REPEATED OR PROLONGED LIQUID CONTACT MAY CAUSE SKIN
IRRITATION W/DISCOMFORT & DERMATITIS. INHAL :NOT NORMALLY HAZARD
UNLESS SPRAYED, THEN OVERSPRAY & SPRAY MISTS ARE PRIMARILY
CONSIDERED NUISANCE (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:DUST. PIGMENTS ARE NOT NORMALLY
CONSIDERED HAZARDOUS WHEN PRESENT IN PRODUCT MIXTURE.
Medical Cond Aggravated by Exposure:PRE-EXISTING CONDITIONS INVOLVING
SKIN DISORDERS.

First Aid

First Aid:INHAL:REMOVE TO FRESH AIR. IF NOT BRTHG, GIVE ARTF RESP, PREF
MOUTH-TO-MOUTH. IF BRTHG DFCLTY PERSISTS/OCCURS LATER, CALL MD.
EYE:IMMED FLUSH W/PLENTY OF H*2O FOR @ LST 15 MIN. CALL MD.
SKIN:WASH W/SO AP & H*2O. IF IRRIT OCCURS, CALL MD. INGEST:CALL MD
IMMEDIATELY.

Fire Fighting

Flash Point Method:TCC
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. COOL CLSD CNTNRS W/WATER FOG TO PREVENT PRESSURE BUILDUP.
Unusual Fire/Explosion Hazard:NONE REASONABLY FORESEEABLE.

Accidental Release

Spill Release Procedures:VENTILATE AREA. PREVENT SKIN CONTACT &
BREATHING OF VAPOR. CONFINE & REMOVE W/INERT ABSORBANT MATERIALS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:OBSERVE LABEL PRECAUTIONS. KEEP
CLOSURES TIGHT WHEN NOT IN USE. STORE IN UPRIGHT POSITION TO
PREVENT LEAKAGE. DO NOT STORE ABOVE 120F.
Other Precautions:KEEP & STORE OUT OF REACH OF CHILDREN. DO NOT SAND,
FLAME CUT, BRAZE/WELD DRY COATING W/OUT NIOSH/MSHA APPRVD
RESP/APPROP VENT. CNTNRS OF THIS MATL MAY BE HAZ WHEN EMPTIED.
SINCE EMPTY CNTNRS RETAIN R ESIDUES, ALL HAZ PRECS MUST BE (SUPDAT)

Exposure Controls

Respiratory Protection:FOR BRUSH & ROLLER APPLICATION, RESPIRATORY
PROTECTION IS NOT NORMALLY REQUIRED. FOR SPRAY APPLICATION, A
PROPERLY FITTED NIOSH/MSHA APPROVED VAPOR/PARTICULATE RESPIRATOR IS
RECOMMENDED.
Ventilation:MECH (GEN) VENT OR LOC EXHST VENT SUFFICIENT IN PATTERN &
VOL TO KEEP VAPS BELOW APPLIC OSHA REQUIREMENTS.
Protective Gloves:SOLVENT IMPERVIOUS GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:COVERALLS ARE RECOMMENDED. SAFETY SHOWER &
EYE BATH.
Work Hygienic Practices:WASH THORO AFT HNDLG & BEFORE EATING & SMOKING.
WASH CONTAM CLTHG BEFORE REUSE.
Supplemental Safety and Health
OTHER PREC:OBSERVED. WHEN SPRAYING THIS MATL KEEP SPRAY BOOTH CLEAN.
AVOID BUILDUP OF SPRAY OR OVERSPRAY IN BOOTH/DUCTS.

Chemical Properties

Boiling Pt:B.P. Text:212F,100C
Vapor Pres:23
Vapor Density:1.3
Spec Gravity:1.2
Evaporation Rate & Reference:0.2 (BUTYL ACETATE=1)
Solubility in Water:MODERATE
Appearance and Odor:MILKY WHITE & CLEAR TO VARIOUS COLORS W/FAINT
AMMONIA ODOR.
Percent Volatiles by Volume:67

Stability

Stability Indicator/Materials to Avoid:YES
NONE REASONABLY FORESEEABLE.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Disposal

Waste Disposal Methods:DO NOT ALLOW MATL TO CONTAM GROUND H*2O SYS.
ABSORB LG SPILLS W/INERT ABSORB MATL. INCIN/DISPOSE ABSORBED MATL
I/A/W FEDERAL, STATE & LOCAL REQUIREMENTS. DO NOT INCINERATE IN
CLOSED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.